Sweet tube tone and loads of unusual features.

The first question everyone asks about the Workhorse Pony amp is, "What's up with that Hubcap speaker grill?" Well it's not there just to look cool. It's actually a carefully designed, patent pending, sound dispersion speaker grille.

Guitar speakers tend to be highly directional. Stand directly in front of any amp, with your ears at speaker level, and you'll get blasted by treble. Walk two steps to the right or left and it sounds like a blanket just got thrown over your amp. Not so with the Hubcap on Workhorse amps.

The Hubcap blocks those nasty ice-pick highs from the center of guitar speakers, and takes all the good full range sound and spreads it out almost 180 degrees. Once you've tried it, you'll wonder how you ever lived without it. If the brushed chrome look is a bit much for your more traditional tastes, take it off, spray paint it black (or any other color) and put it back on you can customize it any way you like.

When you put new tubes in most amps, you have to bring it to an amp tech to have him bias the power tubes for you normally about a $75 job. With the Workhorse Pony amp, you can say goodbye to your amp tech.

Once the amp is fully warmed up, you take the ceramic screwdriver provided with the amp (or any other Phillips screwdriver), put it through one of the lower holes on the back panel of the amp and turn the pot inside until the LED above it turns green. If it turns red, the tube is biased a bit too hot. If the LED is off, the tube is biased a bit too cold.

That's all there is to it. You can bias your power tubes in about 10 seconds with no knowledge of electronics required.

The Workhorse Pony comes with 6L6 power tubes stock. However, if you prefer EL34 power tubes, no problem. Under the chassis is a tube selector switch that you can set for 6L6, 6L6 Hot, EL34, or EL34 Hot. Just install your tubes, set the selector switch, and bias the tubes yourself with the easy user-biasing system.

Bob Weil and R.G. Keen put a huge amount of thought into the construction of the Workhorse Pony amp. They even visited amp techs and asked them, "What do you hate about the amps you work on?" With the boatload of information gained from asking that question, they made sure to design amps that didn't have any of the shortcomings of most amps made these days.

All the jacks and pots are hand-wired to the circuit board. Speaking of circuit boards, those in the Workhorse amp are military-spec; double-thickness boards with triple-thickness copper. No big power resistors to step down voltage like you see in other amps. Those can heat up so much that the solder melts and the resistor can fall right out of the amp. Visual sound uses precision voltage regulators with heat-sinks instead you'll never have to worry about them falling out.

Horizontal metal ribs on the circuit board keep the circuit board absolutely stiff and un-flexible. One of the common causes of failure in many modern amps is circuit board flexing that causes solder pads and traces to break. That won't happen with the Workhorse. If anything ever does go wrong with a Workhorse, the back of the metal chassis opens up like the hood of a car for easy and fast servicing. That means less tech hours and less money to repair. There are fuses on all the transformer outputs, so if something goes really wrong in the amp you'll only need to replace a 5 cent fuse not a $250 transformer!

The Workhorse Pony is simple to use. There are only 5 knobs: Volume, Treble, Mid, Bass, and Reverb for controlling the on-board spring reverb. You don't need to read the manual to figure out how to get good tone. Most guitar players use an array of pedals to get different tones, from overdrive and distortion to chorus and delay.

The Workhorse Pony was created to make effects pedals sound the way they were designed to sound. As many players have done for years, you just run all the pedals into the front of the amp no effects loop required.

To prove the point, Visual Sound even includes a Jekyll & Hyde Overdrive/Distortion pedal to provide a "second and third channel" for the amp. While the Jekyll & Hyde is a great pedal to use with many amps, it really shines with the Workhorse. Whether you play blues or metal or anything in between, the Jekyll & Hyde will inspire you. Just think of it as a channel switcher with knobs!

All Workhorse amps have a Line Out jack on the control panel. Unlike the line out or direct out jacks found on many amps, the Line Out jack on Workhorse amps has a very good speaker simulator circuit behind it. So, if your sound engineer doesn't want to mic the amp, you can simply run a cable from the Line Out jack to a direct box connected to the mixer. A couple of tweaks at the mixer, and your Workhorse will sound just as good through the PA as it does on stage. You'll still be able to hear it through the speaker in the amp, which will simply add to the sound heard through the PA.

The Workhorse Pony combo amp has a 9VDC output jack with a 12 foot (4 meter) cable included with the amp for powering the Jekyll & Hyde pedal. Hook up a daisy-chain cable to the end of the 9V cable and you can power your pedalboard right from the amp. The 9VDC output can handle up to 200mA of current, so you can't plug in Line 6 modeling pedals like the DL4 or other high-current pedals, but the average pedalboard with a handful of pedals can be powered just fine.

Since the Workhorse Pony is the ideal amp for small gigs, there is a CD Input jack on the control panel. So, if you're playing along with tracks at a small gig (or even at home), just plug your CD or mp3 player into the CD Input jack. You can even plug in a POD or other modeling pre-amp into the CD Input jack if you want to bypass the Workhorse pre-amp, but take advantage of the all-tube power amp.

Some amps come with a cover, many do not. But a cover like the Workhorse amp cover is one of a kind. It's nicely padded and even has large pockets on both sides to hold the power cable, 9VDC cable, ceramic tube-biasing screwdriver, manual even the Jekyll & Hyde pedal will fit!

The Celestion Seventy 80 speaker has excellent, tight low-end response, nice glassy highs, and just the right amount of mid-range for a great clean tone and it complements effects pedals perfectly. It can stand up to the huge low-end put out by the Jekyll & Hyde, while still sounding pristine and warm with a chorus pedal like the H20.

Visual Sound Workhorse Pony Tube Guitar Combo Amp Features:

• Celestion Speaker
• 9VDC output & cable for powering effects pedals
• Hubcap sound dispersion speaker grill (Pat. Pending)
• Makes the amp sound great anywhere on the stage
• Protection circuitry throughout the amplifier to prevent failure of all critical components
• Revolutionary easy user-biasing Change Tubes without paying an amp tech!
• Hand wired controls and jacks
• Toroidal power transformer
• All wood cabinet
• Volume, Bass, Mid, Treble, & Reverb controls
• 5 knobs simple!

Let that Pony run! Call or click today to get yours.

Visual Sound Workhorse Pony Tube Guitar Combo Amp Specifications:

• 42lbs. (19.1K)
• 18.25" x 17" x 12"base/11" top (46cm x 43cm x 30 cm base/28 cm top)

Visual Sound Workhorse Pony Tube Guitar Combo Amp

Write A Review

Average of 2 User Ratings

Overall

Quality

Features

Value

Customer Reviews

Overall

Quality

Features

Value

Finally, an amp I love...

Posted by c. bernie from Colorado on Apr 18, 2008

Experience w/product: I own it

Reviewer's Background: 28 years of rock, jazz, punk and country.

Reviewer's Play Style: Mostly Rock and Indie

Fantastic amp, perfect tone...everyone in my band loves this amp. Sonically perfect; the Workhorse Pony is the amp I have been listening for. The sound dispersion grill (the hub cap) projects sound about 160 degrees making this little beaut a listening delight whether you're sitting to the front left, center or front right. The controls are simple; volume, treble, mid, bass and a spring reverb. Very clean with great depth to the volume and the spring reverb sounds 3-dimentional. The Pony delivers volume, for a 30 Watt amp I was pleasantly surprised. I believe it projects such an even, large amount of sound due to the Workhorse's sound dispersion grill; truly an engineering feet in guitar amplification. Tube works and wiring are superb, and the Jekyl and Hyde pedal is just icing on the cake. Kranking it up to new sonic heights, I just love this amp/pedal combo. Rock, metal, funk, punk, jazz, country...this amp can easily do it all. Biasing the tubes is simple and fun, and does take less than one minute...very cool indeed. I believe this is the future in amp modification, and we will be seeing more guitar amp manufacturing copys of the Visual Sound Workhorse. The industry has a new standard. Nice job guys.

Bernie

Overall

Quality

Features

Value

An honest to goodness great amp!

Posted by Jangle junkie from Northern CA on Oct 13, 2007

Experience w/product: I own it

Reviewer's Background: 30 years of gigging and carousing about

Reviewer's Play Style: Wide range of pop incl. 60's garage to surf

After stumbling across this amp in the "others" section and needing a great sounding, easily portable amp I thought I'd take a chance on one of these and couldn't be happier. Solidly built, fantastic, quality features, and superb sound. These amps need to be featured in the product reviews as folks are missing out on a monster of an amp. Basic controls, one input, no onboard overdrive or distortion, just warm and balanced tube tone that will make anyone and any pedal sound better.

If you would like to write a review, please see our product review guidelines.

Visual Sound Workhorse Pony Tube Guitar Combo Amp

Read 2 Reviews

We're sorry, this product has been discontinued.

Item Note:

Gold Coverage Protection Warranty: (What's this?)